astm pipe specification chart
The standards in this compilation were published and are copyrighted by ASTM International. The grouping of standards included have been selected by the American Concrete Pipe Association and may not be inclusive of all ASTM standards related to the subject.
ASTM A106 is the standard specification for seamless carbon steel pipe applied for high temperature services. Dimensions Schedule Range The standard covers pipe sizes in NPS (National Standard Straight) from 10.3mm DN6 1219mm DN1200 (1/8 inch to 48 inch), complied with ASME B 36.10M. ASTM A106 Pipe Specifications American Piping ProductsJun 12, 2015 · American Piping Products stocks a full range of A106 pipe (SA106 Pipe) in:Grades B and C. NPS
ASTM A333 Grade 6 Pipe is a carbon steel pipe that comes under ASTM, ASME and API standards. There are grades 1 through 11 in the pipe series and the sizes range from ½ inches to 36 inches. The wall thickness of the pipes range from 3mm to 12mm and the ASME SA 333 GR 6 Seamless Pipe come under different schedules such as sch40, sch80 and up to XXS including all schedules. ASTM A53 Grade B Pipe and SCH 40 SA 53 Gr.B ASTM A53 Grade B Pipe is a material grade of carbon steel pipes that are intended for low pressure services such as plumping. There are many varieties such as black, galvanized, hot dipped, zinc coated, steel and seamless.
The ASTM A778 tp304l can come in outer diameters ranging from ¼ inches to 60 inches depending on the specification, standards and application requirements. The production type can vary such as the ASTM A778 stainless steel Welded Tubes , seamless tubes, cold drawn or hot rolled tubes. ASTM D1785 and ASTM F441 - PVC and CPVC Pipes Standard dimensions and weight of PVC - Polyvinyl Chloride - and CPVC - Chlorinated Polyvinyl Chloride. Typical weight and dimensions of industrial PVC and CPVC pipes equal to steel pipes schedule 40 and 80 are indicated in the table below. ASTM D1785 Standard Specification for Poly (Vinyl Chloride) (PVC) Plastic Pipe, Schedules 40, 80, and 120 is manufactured to meet the needs of
Standard Specification for Joints for Concrete Pipe, Manholes, and Precast Box Sections Using Pre-formed Flexible Joint Sealants ASTM C1433-10 Standard Specification for Precast Reinforced Concrete Monolithic Box Sections for Culverts, Storm Drains, and Sewers HDPE CORRUGATED PLASTIC PIPEASTM F 405 - Standard Specification for Corrugated Polyethylene (PE) Pipe and Fittings, 3-6 ASTM F 667 - Standard Specification for 8 through 24 inch Corrugated Polyethylene Pipe and Fittings ASTM F 2306 - Standard Specification for 12 to 60 inch (300mm to 1500 mm) Annular Corrugated Profile-Wall
MEETS ASTM D2513, OIL & GAS GATHERING PIPE MEETS API 15 LE for a better tomorrow POLYETHYLENE BLACK GAS or classes not re ected in these charts, including ASTM D2513, the standard specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings, IRRIGATION P.I.P. - JM Eagleindustry accepted P.I.P. (irrigation) pipe standards. Pipe 6" through 27" in diameter are produced in accor- dance with the Natural Resources Conservation Service PIPE ASTM TEST METHOD Hoop Stress at 73º F Minimum Short Term Bursting Strength (psi) or classes not re ected in these charts
Insulation Materials Specification Chart from the NIA National Insulation Training Program This chart provides the reader with material properties as typically specified in ASTM material specifications and is a guide to performance characteristics, but may not be sufficient for writing MATERIAL DATA SHEETS FOR PIPING - StandardNORSOK STANDARD COMMON REQUIREMENTS MATERIAL DATA SHEETS FOR PIPING M-CR-630 Rev. 1, December 1994 Welded pipes Seamless pipes Forgings Plates ASTM A 234 API 5L ASTM A 106 ASTM A 105 ASTM A 516 WPB B B - 60 - - - - - - - - - -SCOPE This MDS specifies the selected options in the referred standard and additional requirements
Plastic Pipe Standards. ASTM's plastic pipe standards are instrumental in specifying, testing, and evaluating the physical, mechanical, design, and installation requirements for plastic, polymeric, or elastomeric pipes, tubing, and fittings, including the seals, threads, and couplings that join them together. Such products are intended for use in high pressure storage vessels, water distribution systems, Stainless Steel Pipe Specifications - China Guanyu ASTM A 358 (ASME SA -358 is generally identical with some additional requirements) This specification covers stainless steel pipe intended for high temperature and general corrosive service. Production is generally limited to diameters and schedule wall thicknesses of 8 and larger as shown in ANSI B36.10 and ANSI B36.19 (See page 4.40).
For example,the ASME B16.5 standard covers the pipes from ½ inches to 24 inches in outer diameter. The ASME B16.9 covers the outer diameters ranging from 26 inches to 60 inches, but Please check the tables below for the charts. Stainless Steel Pipe and Tubing ASTM Specification & Tolerances. oshwin 2 Specification Allowable Outside Standard Specication for Pipe, Steel, Black and Hot 2.2 ANSI Standards:ASC X124 B1.20.1 Pipe Threads, General Purpose4 2.3 ASME Standard:B36.10M Welded and Seamless Wrought Steel Pipe5 2.4 Military Standards:MIL-STD-129 Marking for Shipment and Storage6 MIL-STD-163 Steel Mill Products Preparation for Shipment and Storage6 2.5 Federal Standards:Fed. Std. No. 123 Marking for Shipment (Civil Agencies)7
A182 - A182/A182M-99 - Specification for Forged or Rolled Alloy-Steel Pipe Flanges, Forged Fittings, and Valves and Parts for High-Temperature Service. A252 - A252-98 - Specification for Welded and Seamless Steel Pipe Piles. A312 - A312/A312M-00 - Specification for Seamless and Welded Austenitic Stainless Steel Pipes.